PT5326 Versatile Paste Epoxy Resin
DESCRIPTION
PT5326 is a very smooth epoxy paste resin which lends itself to a variety of splining, filling and patching applications. Its creamy texture permits easy fairing down to a feather edge with a minimum of drag. PT5326 is a versatile resin that has been widely used in applications such as: Embedding Locating & Support Plates for Large Equipment, General Adhesive Bonding of Dissimilar Materials, Surface Patching and Repairing of Tools and Parts, Splining Master Models and Mock-Ups
PRODUCT SPECIFICATIONS
PT5326 A | PT5326 B | ASTM Method | |
Color | Tan | Blue | Visual |
Viscosity | Light Paste | Paste | D2392 |
Specific Gravity, gms./cc | 1.55 | 1.01 | D1475 |
Mix Ratio, by Weight | 100 : 7 | PTM&W | |
Pot Life, 4 fl oz Mass @ 77°F | 15 – 20 min. | D2471 |
HANDLING & CURING
PT5326 will cure completely at room temperature, and needs no added heat
for full cure. The fast pot life of this system is designed to allow
quick turnaround on patching or repair applications. At normal ambient
temperatures (75°F minimum), PT5326 gains handling strength in 4 to 6
hours. At these temperatures, the material will reach full cure in 24
hours, but in colder conditions it will take longer. The cure can be
accelerated by a heat cure of 1 to 2 hours at 150°F, after the material
gels at room temperature.
PACKAGING WEIGHTS
Gallon Kit | Pail | |
PT5326 Part A | 12 lb. | 60 lb. |
PT5326 Part B | 1 lb. | 4.5 lb. |
Kit | 13 lb. | 64.5 lb. |
Inasmuch
as PTM&W Industries, Inc. has no control over the use to which
others may put material, it does not guarantee that the same results as
those described herein will be obtained. The above data was obtained
under laboratory conditions, and to the best of our knowledge is
accurate. This information is presented in good faith to assist the
user in determining whether our products are suitable for his
application. No warranty or representation, however is intended or
made, nor is protection from any law or patent to be inferred, and all
patent rights are reserved. Before using, user shall determine the
suitability of the product for his intended use, and user assumes all
risk and liability whatsoever in connection therewith. In no event with
PTM&W Industries, Inc. be liable for incidental or consequential
damages. Buyer’s sole and exclusive remedy in such instances shall be
limited to replacement of the purchase price.
TYPICAL MECHANICAL PROPERTIES
PT5326 A/B | ASTM Method | |
Mix Ratio, by Weight | 100 : 7 | PTM&W |
Color | Light Blue | Visual |
Mixed Viscosity, @77°F, centipoise | Thixotropic Paste | D2393 |
Pot Life, 4 fl. oz. Mass @ 77°F | 15 – 20 min. | D2471 |
Cured Hardness, Shore D | 86 Shore D | D2240 |
Specific Gravity, grams, cc | 1.54 | D1475 |
Density, lb./cu in, lb./gallon | .0556, 12.9 | D792 |
Specific Volume, cu. in./lb. | 17.9 | D792 |
Tensile Strength, psi | 3,750 psi | D638 |
Flexural Strength, psi | 6,500 psi | D638 |
Compressive Strength, psi | 12,000 psi | D695 |
Maximum Service Temperature | 190°F – 200°F | PTM&W |
SAFETY & HANDLING
PTM&W epoxy products are made from raw materials carefully chosen to minimize or even eliminate toxic chemicals, and therefore offer the user high performance products with minimum hazard potential when properly used. Generally, the PTM&W epoxy resins and hardeners will present no handling problems if users exercise care to protect the skin and eyes, and if good ventilation is provided in the work areas. However, all epoxy resins and hardeners can be irritating to the skin, and prolonged contact may result in sensitization; and breathing of mist or vapors may cause allergenic respiratory reactions, especially in highly sensitive individuals. As such, avoid contact with eyes and skin, and avoid breathing vapors. Wear protective rubber apron, clothing, gloves, face shield or other items are required to prevent contact with the skin. In case of skin contact, immediately wash with soap and water, followed by a rinse of the area with vinegar, and then a further wash with soap and water. The vinegar will neutralize the hardener and lessen the chances of long term effects. Use goggles, a face shield, safety glasses or other items as required to prevent contact with the eyes. If material gets into the eyes, immediately flush with water for at least 15 minutes and call a physician. Generally, keep the work area as uncluttered and clean as possible, and clean up any minor spills immediately to prevent accidental skin contact at a later time. Keep tools clean and properly stored. Dispose of trash and empty containers properly. Do not use any of these types of products until Material Safety Data Sheets have been read and understood.